Home | Gallery | Forums | Ads | Store ANTIQUETRACTORS.COM

AntiqueTractors.com Antique Tractor Resource Page

   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   H. Ferguson John Deere Massey Minn. Moline Oliver

Marketplace
Tractor Manuals
Tractor Parts
Engine Kits
Classified Ads
Photo Ads

Community
Discussion Forums
Collector Profiles
Show Guide
Guest Book

Galleries
Tractor Photos
Garden Tractors
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads

Research Center
Tractor Values
Production Numbers
List Prices
Tune-Up Specs
3-Point Specs
Spark Plug List
Torque Values
Torque Specs
Plow Specs
Terminology
Clubs & Pubs
JD New Generation
JD HP Chart

Miscellaneous
Today in History
Pic of the Day
Table of Contents

Related Sites
Garden Tractors
The Tractor Shed
Ford 9N/2N/8N Club
Yesterday's Tractors
More Sites

Tractor Stories

Return to List

Just in Case

I'd like to preface this info by saying that I found this site while looking for suggestions on replacing the fan-belt in my Case 580CK loader/backhoe. I live out in the stix,first of all so I need to drive about 10mi if I need diesel fuel which sometimes causes me to run on a low fuel tank. Normally this can be done without problems but my property (especially my driveway)is on a hill and if the tank is low and the machine is on a bad angle the fuel will slosh away from the pickup in the tank and the machine dies. This can be a real pain in the *#+ if I'm trying to clear snow to get out to the road. The biggest problem is that with a loss of fuel flow for a moment, you lose the prime to the injector pump. If you've ever tried to reprime these units you'll know what I'm talking about. The line comes out of the tank and goes down almost to the level of the bottom of the block, is then routed through two filters then turns upward to come back up to the injector. Its a real convuluted set-up. Well one time it happened and I was in a pickle because the machine was halfway to the road in the middle of the driveway and no one could get in or out. It was also about -5 F outside. After about an hour of trying to prime it I went in the house to get a hot coffee. I wasn't really welcome in the house because I'd succeeded in making everyone late so I went out to the shop to have my coffee in peace. While I was sitting there, cursing my bad luck, my eyes came to rest on a remote-mount diesel fuel filter/water trap (that I had bought at an auction in a job lot with some other stuff) just sitting there on the shelf. At that moment it came to me! I would bypass the original filter and lines using this one! I quickly set about fabbing a piece of 0.25 plate on which to mount the filter, then I went down to the machine to locate a suitable mounting location and came back to finish fabbing the mount. The end result being a filter system that is approx. 1' below the outlet on the tank and about 3' above the level of the inlet on the injector pump. Voila! A gravity-feed fuel system that doesn't require priming and works like a charm. I recently helped a buddy fab a similar bypass for the hydr line from the reservoir to the hydr pump on his AC tractor. His 3 pt hitch has never worked better. I realise that this sort of modification is a no no in restoration circles, but sometimes there's a simpler way to achieve the same ends.

Albert, NY, entered 2011-07-30
My Email Address: Not Displayed

Return to List


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2022 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy